How to put the tile in the bathroom with your hands?

Putting a tile in the bathroom with your own hands is a processnot easy, especially if you do it for the first time. It will also take a lot of time to decide on the exact design, and therefore you will have to visit the hardware store more than once.

How to choose the material correctly?

In order to put the tiles in the bathroomwith your own hands, first of all, you should make the most accurate calculations regarding the amount of material. Not all stores practice returning tile residues, but there may be another problem - the product may not be available. You can buy a tile of a similar color or appearance, however, in the process of repairing, the difference will become more expressive and for a long time it will make your room to an eyesore.

At home, you need to draw a tile layout plan,preferably as close as possible. This will not only help to take into account the number and size of the required tile, but also help to find places where tile cuts will be the least noticeable.

The material can not be saved, because in this case, the price category really plays a big role. It is because of the high cost of tile you need to plan in advance laying.

How to choose a color?

A tile, like any other item usedin interior design, is able to hide the disadvantages of the room, as well as emphasize its advantages. But how to make the right choice? Need to understand more.

With the help of non-standard tiles you can make an unusual even the most ordinary bathroom, and therefore you need to familiarize yourself with the full range of possible colors and textures of tiles.

As in any other interior, the bright colors of the tiles will visually expand the room, and warm colors will help to achieve complete relaxation.

It is better to abandon the usual option with blueor green tiles. After all, it can destroy the uniqueness of any bathroom. If a similar color has already been selected, it is better to add some interesting ornament to it or make sure that there are other bright details in the bathroom.

Bright colors are recommended for use only.making any accents in the room. If you completely cover the room with such tiles, it will interfere with concentration and relaxation, and also quickly tire your eyes and make you think about re-repairs.

Glue selection

To put a tile in the bathroom with their own hands,need to take care of acquiring the appropriate glue. The most popular is a mixture of CM11, but it can only be used if your bathroom has no special conditions that can make the process of gluing tiles more difficult. The price of this glue is very democratic, and its quality is time tested.

Preparation of premises

The preparation of the room must be approached with specialcaution, especially if replacing any of the plumbing is not currently in your plans. The toilet and washbasin should be carefully removed. However, this can be done only after closing off the supply of hot and cold water.

Dismantling the old coating: can we do without it?

Before putting tiles in the bathroom, many room owners are wondering if they really need to dismantle old material. The answer is simple: it all depends on her condition.

If the old tile is in fairly good conditionand never disappears, it is possible to mount the tile and on it. To do this, it is only necessary to thoroughly rinse the previous layer and with special care to treat the seams between the plates.

If the old tile is in an emergency condition, it, undoubtedly, needs to be dismantled. For these purposes, perfect puncher, which must be put into shock mode.

We need to take care of their own security.before you put the tiles in the bathroom. In the process of dismantling from the material, most likely, will fly off pieces. That is why it is better to find gloves and goggles.

If the old tile disappears along with the layers of glue and / or plaster, there is no need to worry, because the glue will have to be removed in any case. Plastering the room is also recommended anew.

Aligning walls

Rarely the walls in high-rise buildings, especially brick or concrete, are smooth. In this case, they just need to align, otherwise the repair does not make any sense.

If the walls are not strong enough, they are recommended to be primed before leveling. It is recommended to repeat and before putting tile in the bathroom. But this is not all the nuances of work.

How to put the tiles in the bathroom next? To determine how much work to do, you need to take the angle and plumb line. The latter must be used to determine the deviation of the wall from the vertical. The square will help measure the degree of deviation.

After the primer has dried, it is necessaryfasten the beacons on the wall. To do this, apply glue in several places, and then fix the beacons alternately. Equipment must necessarily be in the same vertical plane.

The process of leveling the walls: what is it?

After fixing the lighthouses need to fillthe gap between the wall and the mounting solution. As a rule, use ordinary cement mortar. However, it is better to change one part of the cement to one part of the glue. This will add more strength before laying tiles in the bathroom on the wall.

Further, by sharp and short movements (in thiscan help trowel or bucket) need to apply the solution. Need to start from the top of the wall. However, if this is too difficult for you, you can start at the bottom.

Every time the gap between the mountsfilled, with the help of the rule you need to get rid of the residual solution It is better to return the excess amount of solution back to the tank. The process must continue until all gaps are filled.

Floor leveling

Before you put the tile in the bathroom, you need to take care of the alignment of not only the walls, but also the floor. Here there are two ways:

• With the help of lighthouses.
• With self-leveling compound. However, this method does not apply to a number of cheap.

Not always the bathroom floor needs alignment,which is easiest to measure with a laser level. If the distance between the laser marks on the wall and the floor is the same or less than five millimeters, then you can do without adjusting the level at all. Small curvature correct directly in the process of laying tiles.

If the deviation was revealed, before laying the tile on the floor in the bathroom, you need to repeat the same procedure as with the walls. The only difference is that the lighthouses must be clearly marked.

Finish

In the question of how to properly put tiles inbathroom, you need to remember that you should always start with the walls. First you need to calculate the number of whole tiles on one wall, taking into account the fact that the distance between them should be no more than five, but not less than three millimeters.

If a non-integer is obtained, the tile will have to be cut. Aesthetically trimmed tile will look at the bottom (where it least attracts attention).

However, starting to lay the bottom is notIt is recommended, and therefore it is necessary to measure the height of the scraps approximately and install a wooden lath at this level. Now you can safely start laying on top.

Preparation of the solution

To properly prepare the mixture, you first needPour into a container of water, and then gradually add the dry mixture. The solution must be constantly stirred with a construction mixer in order to give it a thickening.

A large amount of the solution immediately do not need. After all, it will dry out. It is better to be limited to small portions that can be constantly replenished.

The result should be a mixture similar togruel. However, it should not flow down from the tile or from the walls, but stretch evenly over the surface. If the solution looks like this, you can proceed to the next process.

Laying tiles on the wall

Obtained during the previous step, the solution must be applied to the tile and press it to the wall. Each tile should be located exactly above the level.

During the installation you need to use specialplastic crosses. They will help control the gap between the plates. Despite the fact that the gap always wants to be neglected, it is important enough for the long preservation of repairs. The fact is that the distance between the plates helps to prevent the occurrence of cracks in the material due to thermal expansion. In addition, the crosses will help to make the seams relatively identical. This has a positive effect on appearance.

Before we put the tiles in the bathroomon your own, it is recommended to tighten the thread (horizontally) for the second row. This will significantly reduce the time for repair and will help not to recheck the level of each tile separately.

When you need to put very small pieces, theirIt is best to place in the corners (where they will not be visible). It is important to comply with the level. After all, if the tile goes a little downhill, it will be quite noticeable. This will significantly ruin the overall impression of even the most expensive material. We can not allow even the slightest displacement of the rows.

Laying tiles on the floor

Asking how to put tiles in the bathroom, you are most likely interested in the process of laying tiles on the floor.

Although, basically, the styling processtile on the floor is no different from the finish of the wall, it has its own nuances. Always start only from the far wall. And then move towards the door.

In the case of laying on the floor is also necessarytighten the nylon thread to prevent displacement in a particular segment. The tile can be set to the desired level with a rubber hammer. But do not overdo it, if the material has gone too deep, then it will have to be removed and then re-laid.

Final stage: grout

When the last tile has fallen into place, the entire structure must be cleaned of glue, until it is completely absorbed, and then let the mixture dry and grow strong.

How beautiful to put the tiles in the bathroom? After laying, you need a couple of days (ideally three or four) not to enter the room with the repair. It is better to open the windows in the apartment and let the smell of glue erode.

After the material is completely dry,You can proceed to the process of grouting. On the grout itself is not worth saving. After all, not only the appearance but also the durability of the new repair will depend on its quality. By the way, the grout can be of several types. There are finished products in the form of a solution. The first is sold in tubes under the gun. The second is a powder that must be diluted with water for further use on the surface of the wall or floor.

The best quality is considered fine grout, which will last for many years. Poor grout will have to be changed in a few years.

After the material has been applied, it is best to immediately get rid of the excess. The fact that the grout is sometimes difficult to remove. This is especially acute for tiles with a bright or textured design.

conclusions

Laying tiles in the bathroom is almost the same as the walls and floor, but this process has its own subtleties for each surface, and it is simply impossible to forget about them.

The choice of tile in the bathroom may depend on comfortall family members over the years, and therefore no need to be irresponsible to this process. It is better to pay attention to the manufacturer, price and even the color of the tile. The bathroom is a place to relax, and some details in the interior can be very distracting.

Tiles in the room are used becauseIt is most convenient, stable and has many positive characteristics. For example, the material is not afraid of moisture, it can be easily treated with detergents. The tile does not peel off when interacting with steam or hot water, which is not the case with wallpaper. The material will last and keep its appearance unchanged much longer than any other type of coating.

As can be understood from the above, tileNot only is it enough to just put it, but it is easy to use and most picky. Even a novice in construction will be able to cope in order to make high quality tile laying. However, this may take a little more time than the professionals.